Jeep Wrangler JK 2007-2018, RockJock Currectlync High Steer Trac Bar Relocation & Ram Assist Mount Axle Bracket Kit
Jeep Wrangler JK 2007-2018, RockJock Currectlync High Steer Trac Bar Relocation & Ram Assist Mount Axle Bracket Kit
Jeep Wrangler JK 2007-2018, RockJock Currectlync High Steer Trac Bar Relocation & Ram Assist Mount Axle Bracket Kit, view 2
Jeep Wrangler JK 2007-2018, RockJock Currectlync High Steer Trac Bar Relocation & Ram Assist Mount Axle Bracket Kit, view 2
Jeep Wrangler JK 2007-2018, RockJock Currectlync High Steer Trac Bar Relocation & Ram Assist Mount Axle Bracket Kit, view 3
Jeep Wrangler JK 2007-2018, RockJock Currectlync High Steer Trac Bar Relocation & Ram Assist Mount Axle Bracket Kit, view 3
Jeep Wrangler JK 2007-2018, RockJock Currectlync High Steer Trac Bar Relocation & Ram Assist Mount Axle Bracket Kit, view 4
Jeep Wrangler JK 2007-2018, RockJock Currectlync High Steer Trac Bar Relocation & Ram Assist Mount Axle Bracket Kit, view 4
Click to open expanded view

Jeep Wrangler JK 2007-2018, RockJock Currectlync High Steer Trac Bar Relocation & Ram Assist Mount Axle Bracket Kit

SKU: RJ-431109-103
In stock and ready for shipping
Price
$342
Add To Wishlist
Vehicle Fitment

2007-2018 Jeep Wrangler JK

Install Instructions

Install Instructions for JK Trac Bar Relocation and Ram Assist Mount (High Steer)

Warning: California Residents

WARNING: Cancer and Reproductive Harm -www.p65warnings.ca.gov

Share this product

Share Post Pin E-mail

Jeep Wrangler JK 2007-2018, RockJock Currectlync High Steer Trac Bar Relocation & Ram Assist Mount Axle Bracket Kit Info & Specs

Raising the steering changes the trac bar geometry, and ignoring that leads to bump steer on every suspension hit. It also leaves no good place to mount a hydraulic assist ram. This RockJock bracket kit raises the trac bar mounting point 2 inches to correct the geometry and adds a solid mounting point for a JL/JT-spec ram, which allows more steering angle. The bottom of the bracket doubles as a skid plate that shields the ram from rocks. A second bracket relocates the sway bar end link on the driver side. The brackets need minor welding, but the supplied bolts hold them well enough to drive to a welder. Fit them, pair them with the high steer knuckles, and the steering geometry stays right.

Key Features

  • Raises the trac bar mounting point 2 in to prevent bump steer
  • Mounting point for a JL/JT-spec hydraulic steering assist ram
  • Bracket bottom acts as a skid plate for the ram
  • Driver side bracket relocates the sway bar end link mount; new holes sit 2 1/8 in higher than stock
  • Supplied bolts hold the brackets solidly enough to drive to a welder

Specifications

  • Fits axle tubes up to 3 1/2 in diameter
  • Hydraulic assist ram stroke needed for full potential: 7.375 in (factory steering radius)
  • Installation: minor welding required; sway bar link lengths must be adjusted
  • Sold as: each
  • Shipping weight: 14.5 lb
  • Shipping carton: 24 x 14 x 7 in

Fitment

  • Jeep Wrangler JK 2-Door 2007-2018
  • Jeep Wrangler JK Unlimited 4-Door 2007-2018

For vehicles with the factory front differential (Dana 30 or Dana 44) or an aftermarket axle with factory-spec inner C-knuckles. Designed to be used with RockJock High Steer Knuckles.

In the Box

  • Trac bar relocation and ram mount bracket (passenger side)
  • Sway bar end link relocation bracket (driver side)
  • Hardware
  • Step-by-step instructions

Notes

  • The RockJock forged front trac bar (RJ-9120FJLF) is mandatory with this kit.
  • Intended for use with common PSC ram assist steering kits.
  • RockJock strongly recommends the adjustable front bump stop kit (RJ-107101-101) for maximum up-travel.


MPN RJ-431109-103 · UPC 810038158716